Skip to content
Resonant — Transformer Manufacturers

From raw material to dispatch.

Every transformer moves through twelve controlled stages. Each one has a purpose, an inspection and a record before the next begins.

Welder fabricating steel with protective gear

Manufacturing journey

Twelve stages, one record.

  1. Engineers reviewing work on the shop floor
    01Material

    Raw Material Inspection

    Core metals, winding wire, radiators, bushings and tap changers are received against purchase orders and checked by QA/QC before release to production.

    • Matched to ERP purchase order and BOM
    • QA/QC acceptance before issue
    • Non-conformance reported to vendor via NCR
  2. Precision cutting of sheet steel
    02Core

    Core Cutting & Lamination

    Electrical steel is cut into laminations to the core design, with attention to dimensions and burr — the foundation of low losses.

    • Lamination dimensions to drawing
    • Edge and burr condition
    • Stack sorting by step
  3. 03Core

    Core Assembly

    Laminations are stacked into limbs and yokes in a stepped cross-section and secured in the core clamping structure.

    • Stack height and step profile
    • Joint alignment
    • Clamping frame fit
  4. Coil of copper winding wire
    04Coil

    Winding Manufacturing

    Primary and secondary windings are wound from conductor with insulation, spacers and cooling ducts built in as specified.

    • Turns and conductor as per design
    • Insulation and duct placement
    • Coil dimensions
  5. 05Coil

    Core & Coil Assembly

    Windings are lowered over the core limbs, the top yoke is re-stacked and the active part is clamped, braced and connected.

    • Concentricity of windings
    • Top yoke interleaving
    • Lead and tap connections
  6. Welder fabricating steel with protective gear
    06Tank

    Tank Fabrication

    Steel tanks, covers and stiffeners are fabricated and welded, then checked for dimensions and leak-tightness before finishing.

    • Weld quality
    • Dimensional check
    • Leak-tightness before painting
  7. 07Tank

    Tanking Process

    The dried active part is lifted by crane and lowered into its tank, positioned and secured.

    • Controlled crane lift
    • Clearances to tank walls
    • Active part locking
  8. 08Processing

    Vacuum & Oil Processing

    Moisture is removed from insulation and the tank is filled with treated insulating oil under controlled conditions.

    • Insulation dryness
    • Oil quality before filling
    • Filling under controlled conditions
  9. Electrical equipment on a production line
    09Processing

    Final Assembly

    Radiators, conservator, bushings, protection devices, indicators and valves are fitted to the customer's accessory specification.

    • Accessories to specification
    • Gasket and joint tightness
    • Wiring and marshalling
  10. Technician testing electrical equipment with a meter
    10Verification

    Electrical Testing

    The completed transformer is tested and the results recorded in technical test reports reviewed by the testing function.

    • Tests per applicable standard
    • Results recorded in test reports
    • Review by testing function
  11. Transformer insulators and connections against a blue sky
    11Verification

    Final Quality Inspection

    A final inspection confirms finish, fittings, nameplate and documentation — and, where required, customer inspection and dispatch clearance.

    • Visual and fitment check
    • Documentation complete
    • Customer dispatch clearance (MDCC) where applicable
  12. 12Delivery

    Packing & Dispatch

    Units are secured on planned trailers or flatbeds with invoices, packing lists, e-way bills, lorry receipts and transit insurance.

    • Vehicle planned to load
    • Statutory transit documents
    • Shipment tracked to delivery
Bright, organised manufacturing floor

On the shop floor

Organised bays, clear hand-offs and an inspection at every step.

Quality & testing

Documented practices

How the process stays in control.

Drawn from Resonant Equipment's own documented workflow across design, procurement, QA/QC, testing and logistics.

Design-led procurement

Purchase orders are raised in an ERP system against the structural Bill of Materials issued by the design team — so every component traces back to the design.

Approved-vendor sourcing

Core metals, winding wire, radiators, bushings and tap changers are sourced from approved vendors, with quotations reviewed against historical benchmarks.

Non-conformance control

Incoming material is checked by QA/QC. Rejected inputs are handled through formal vendor Non-Conformance Reports (NCR) with replacement or rework.

Test reports before dispatch

Technical test reports are completed and reviewed by the testing function before any finished transformer is booked for dispatch.

Customer dispatch clearance

Where applicable, customer Material Dispatch Clearance (MDCC) is obtained before vehicles are booked — no shipment leaves without clearance.

Heavy-haul logistics

Inbound steel and tanks, and outbound finished transformers, move on planned trailers and flatbeds with full statutory transit documentation.

Transmission lines crossing open farmland

Get in touch

Let's engineer your next transformer.

Tell us about your application, rating and site conditions. Our team will respond with the next steps.